Line Voltage Monorail WAC Low Voltage or Line Voltage Monorail Quick Connect Fixtures & Pendants Accessories
This site contains affiliate links for which I may be compensated.

WAC Lighting DuoRail 2-Circuit Monorail Systems

WAC Lighting DuoRail 2-Circuit Monorail System using Pre Bent Duorail Rail Sections with WAC Clarity G916 European Pendants

Customize Your WAC Lighting DuoRail Monorail System

WAC Lighting DuoRail 2-Circuit Monorail on Amazon

WAC Duorail
Two Circuit Monorail System

WAC Duorail is engineered for more capacity and control, with two circuits that can be independently controlled. This allows you to have separate switches or dimmers for lights on the same rail. It can be ordered pre curved or shaped in the field and designed and cut to navigate curves and angles for custom designs. Each circuit uses up to 300 watts at 12 volts or 600 watts at 24 volts. For large applications both circuits can be switched together for up to 1,200 watts at 24 volts. Single Circuit Monorail System WAC Solorail has been retired.

Design your rail.

  • Determine what you want to light.
  • Decide where track heads, pendants or both will be placed to direct light where you want it.
  • Design the Monorail run, connecting the lights.
    Monorail can be shaped to follow room architecture or create an organic shape.
    You can sketch out your room on paper. Draw in your lights, then decide how you want to design the track to suspend them.
    You could use string to lay out your design on the floor to determine your length, especially if you have an especially curvy run.
    Rail is available in connectable four or eight foot sections to be bent in the field as needed or used as a straight section. A bending machine is available to make smooth and consistent bends.
    All rail pieces are field-cuttable and bendable.
  • Connectors allow monorail to make sharp angles or join in a "T" or " x ."
  • Dead-End connectors allow you to switch and dim sections of rail separately.
  • Choose a finish; Brushed Nickel or Dark Bronze.

Determine your mounting.

  • Determine how far from the ceiling you would you like your rail to run.
    WAC Duorail Monorail can be installed nearly flush to the ceiling or hang up to 96".
  • Rail can be curved horizontally or vertically, to run up and down.
  • Rigid or cable suspensions mount to flat, suspended or sloped ceilings using standard, T-Bar or sloped ceilings standoffs.
  • Use 2 supports per 4 foot section and at least 3 per 8 foot section.
  • The total number of supports depends on the shape of the track layout.
  • The power feed counts as a support.
  • Systems with very unique shapes or many pendants may require additional supports.

Choose your lights.

  • Decide where the fixtures should be installed to put light where you want it.
  • Select from an array of low voltage track heads and pendants.
  • Extension stems can extend fixtures up to 48" from the track.
  • Pendants ship with 6' field cuttable cable.
  • Add optional colorful and decorative accessories and functional optical controls.

Select your transformer.

  • Add up the wattage from the lights you have chosen.
  • Choose 12 or 24 volt. 300 watts is the maximum load for 12 volt systems. 600 watts is the maximum load for 24 volt systems.
  • Select a visible surface mount transformer or a hidden remote transformer with power feed canopy.
  • Surface mount transformers install directly to a standard junction box.
  • Remote mount magnetic transformers have larger capacity. They can be installed further away, in an attic or closet.
  • Select your power feed if you are going to use a remote transformer.

(Or start with fixtures and accessories, then decide which layout will best support them.)

WAC Lighting DuoRail 2-Circuit Low Voltage Monorail Installation Instructions & Frequently Asked Questions >

WAC Lighting DuoRail 2-Circuit Monorail with LEDme Forza LED QF-LED173 Quick Connect Fixtures and Uber G315 LED Pendants from the Industrial Collection all in Satin Nickel Finish

WAC Lighting Duorail Pendants and Fixtures

Choose from WAC Lightings vast selection of Pendants in so many colors and styles.

Duorail uses low voltage track heads and pendants. The Duorail system uses LM2 style track heads as well as quick connect track heads and pendants in conjunction with the LM2-QADP quick connect adaptor.

WAC Quick Connect Pendants
Artisan Pendants >
Contemporary Pendants >
Early Electric Pendants >
Eternity Jewelry Collection >
European Pendants >
WAC Quick Connect Fixtures >

Rail

WAC Lighting LM2-T DuoRail 2-Circuit Monorail Systems

WAC Lighting LM2-T DuoRail 2-Circuit Monorail Rail on Amazon

Duorail system allows you the sleek, minimalist look of a low voltage monorail with the advantages of double the load capacity and two circuit switching control. An ideal choice for, residential and commercial applications.

WAC Duorail is a low voltage bendable two circuits track system. 2-Circuit Monorail allows individual fixtures to be independently switched or dimmed. Straight rail is ordered as a four or eight foot sections to be bent in the field as needed or used as a straight section. The rail is field cuttable and bendable by hand or with a bending tool. It can be designed and cut to navigate curves for custom designs.

Duorail is composed of four 2mm thick copper bus wires with a 1.5mm thick polycarbonate core. Each rail also includes two matching polycarbonate endcaps. It is only.25" x 11/16", the thinnest in the industry.

Maximum load carrying capacity of 600W at 12V and 1200V at 24V, with the ability to individually control each circuit.

  • 2 circuit, 12 volt or 24 volt.
  • 600W maximum capacity at 12/24V.
  • Surface or Remote Transformer
  • Magnetic or Electronic Transformer
  • Can use electronic surface mount, electronic remote, magnetic surface mount, or magnetic remote transformers.
  • Mounts to flat, suspended, or sloped ceilings. Use 2 supports per 4 foot section and at least 3 per 8 foot section. Total number of supports used in an application depends on the shape of the track layout. Systems with very unique shapes may require the use of additional supports.
  • Abrasion resistant Brushed Nickel or Dark Bronze finish.
  • The LM2-QADP is compatible with all QF and QP socket sets.
  • Can be suspended from ceiling with cable or rigid standoffs.
  • An optional rail bending tool (HM1- BM) is available for field bending when precise control and very smooth curves are desired.

BN = Brushed Nickel metal finish
DB = Dark Bronze metal finish

5 year WAC Lighting product warranty.
UL & CUL Listed.

LM2-T4-BN 2-Circuit Low Voltage Monorail 4Ft Rail
LM2-T4-DB 2-Circuit Low Voltage Monorail 4Ft Rail
LM2-T8-BN 2-Circuit Low Voltage Monorail 8Ft Rail
LM2-T8-DB 2-Circuit Low Voltage Monorail 8Ft Rail

WAC Lighting LM2-T18R, LM2-T24R, LM2-T36R, LM2-T48R Pre Bent Duorail Rail Sections

Pre Bent Duorail Rail Sections

BN = Brushed Nickel metal finish
DB = Dark Bronze metal finish

5 year WAC Lighting product warranty.
UL & CUL Listed.

LM2-T18R-BN Quarter Section 18" Radius (3' diameter)
LM2-T18R-DB Quarter Section 18" Radius (3' diameter)
LM2-T24R-BN Quarter Section 2' Radius (4' diameter)
LM2-T24R-DB Quarter Section 2' Radius (4' diameter)
LM2-T36R-BN Quarter Section 3' Radius (6' diameter)
LM2-T36R-DB Quarter Section 3' Radius (6' diameter)
LM2-T48R-BN Quarter Section 4' Radius (8' diameter)
LM2-T48R-DB Quarter Section 4' Radius (8' diameter)
LM2-T60R-BN Quarter Section 5' Radius (10' diameter)
LM2-T60R-DB Quarter Section 5' Radius (10' diameter)

Connectors

"T" Connector LM2-T Duorail System

WAC Lighting DuoRail 2-Circuit Monorail T Connector on Amazon

Connects two sections of a monorail in a "T" with electrical continuity.

Dimension: 5/8" x 1 5/8" x 1 5/8"

LM2-T-BN 2-Circuit Low Voltage Monorail T Connector 
LM2-T-DB 2-Circuit Low Voltage Monorail T Connector 


"L" Connector LM2-L Duorail System

WAC Lighting DuoRail 2-Circuit Monorail T Connector on Amazon

90° monorail connection with electrical continuity

Dimension: 5/8" x 1.5" x 1.5"
LM2-L-BN 2-Circuit Low Voltage Monorail L Connector 
LM2-L-DB 2-Circuit Low Voltage Monorail L Connector 


Variable Angle Connector LM2-VA Duorail System

WAC Lighting DuoRail 2-Circuit Monorail T Connector on Amazon

Allows an angle adjustment up to 110° with electrical continuity at the connection

Dimension: 1" x 1.25" x 3.5"

LM2-VA-BN Variable Angle Connector 
LM2-VA-DB Variable Angle Connector 


"X" Connector LM2-XDEC Duorail System

WAC Lighting DuoRail "X" Connector on Amazon

Joins four monorails in an "X" without electrical continuity

Dimension: 5/8" x 2" x 2"

LM2-XDEC-BN 2-Circuit Low Voltage Monorail Dead X Connector 
LM2-XDEC-DB 2-Circuit Low Voltage Monorail Dead X Connector 


"I" Connector LM2-I Duorail System

WAC Lighting DuoRail "X" Connector on Amazon

Connects two sections of rail with electrical continuity

Dimension: 5/8" x 2"

LM2-I-BN 2-Circuit Low Voltage Monorail I Connector 
LM2-I-DB 2-Circuit Low Voltage Monorail I Connector 


"I" Dead-End Connector LM2-IDEC Duorail System

WAC Lighting DuoRail "X" Connector on Amazon

Connects two sections of rail with no electrical continuity

Dimension: 5/8" x 2"

LM2-IDEC-BN  Low Voltage Duorail Dead Straight Connector 
LM2-IDEC-DB  Low Voltage Duorail Dead Straight Connector 


Duorail End Cap LM2-EC

WAC Lighting LM2-EC Duorail End Cap on Amazon

Extra end cap for Duorail. Ordered when doing multiple cuts of a long piece of rail.

LM2-EC-BN 2-Circuit Low Voltage Monorail End Cap
LM2-EC-DB 2-Circuit Low Voltage Monorail End Cap

Bending Machine HM1-BM

Used to make smooth and consistent bends of rail. Two Compact and Mini Picture Lights brackets mount bending machine to table or similar flat surface. Angle indicators on bending machine help the user determine the proper amount of tension.

This same bending machine will bend a variety of monorail.

HM1-BM Bending Machine

Aircraft Suspension Cable LM2-CS Duorail System

WAC Lighting LM2-CS Aircraft Suspension Cable Duorail System on Amazon

Supports monorail for flat or slope ceilings

  • LM2-CS48 - 48"
  • LM2-CS96 - 96"
LM2-CS48-BN  Low Voltage Duorail 48' Aircraft Cable Suspension
LM2-CS48-DB  Low Voltage Duorail 48' Aircraft Cable Suspension
LM2-CS96-BN  Low Voltage Duorail 96' Aircraft Cable Suspension
LM2-CS96-DB  Low Voltage Duorail 96' Aircraft Cable Suspension

T-Bar Drop Ceiling Standoff LM2-TB3 Duorail System

WAC Lighting Duorail System Standoffs on Amazon

Conceals a T-Bar clip under the canopy for standard 1" T-Bar ceilings

  • TB3 -3"
  • TB5 -5.75"
  • TB8 -8"
LM2-TB3-BN 2-Circuit Low Voltage Monorail 3" Standoff 
LM2-TB3-DB 2-Circuit Low Voltage Monorail 3" Standoff 
LM2-TB5-BN 2-Circuit Low Voltage Monorail 5" Standoff 
LM2-TB5-DB 2-Circuit Low Voltage Monorail 5" Standoff 
LM2-TB8-BN 2-Circuit Low Voltage Monorail 8" Standoff 
LM2-TB8-DB 2-Circuit Low Voltage Monorail 8" Standoff 

Standard Ceiling Standoff LM2-X Duorail System

WAC Lighting Duorail System Standoffs on Amazon

Supports rail for flat ceilings and surfaces

  • LM2-X3 - 3"
  • LM2-X5 - 5.75"
  • LM2-X8 - 8"
LM2-X3-BN  Low Voltage Duorail 3' Standard Ceiling Standoff 
LM2-X3-DB  Low Voltage Duorail 3' Standard Ceiling Standoff 
LM2-X5-BN  Low Voltage Duorail 5' Standard Ceiling Standoff 
LM2-X5-DB  Low Voltage Duorail 5' Standard Ceiling Standoff 
LM2-X8-BN  Low Voltage Duorail 8' Standard Ceiling Standof
LM2-X8-DB  Low Voltage Duorail 8' Standard Ceiling Standoff 

Sloped Ceiling Standoff LM2-XS Duorail System

WAC Lighting Duorail System Standoffs on Amazon

Support rail for slope ceiling

Accommodates angles up to 45"

Dimension 5.75"

LM2-XS5-BN  Low Voltage Duorail 5' Sloped Ceiling Standoff 
LM2-XS5-DB  Low Voltage Duorail 5' Sloped Ceiling Standoff 


WAC Lighting Extension Rods LM-R for Solorail Monorail Support

WAC Lighting Monorail Extension Rods on Amazon

  • Use with standoffs and power feed
  • Use two per circuit with rod couplers to extend power feeds
  • Field cut to size and join with rod couplers

Finishes: BN-Brushed Nickel, DB-Dark Bronze

LM-R12 12" Extension Rod
LM-R24  2Extension 4" Rod
LM-R36 36" Extension Rod
LM-R48 48" Extension Rod

Rod Coupler LM-RI
Use two per power feed, four per dual power feed, one additional coupler per rod needed when joining two rods in excess of 48".

Duorail Surface Mounted Transformers

Surface mount transformers mount to a junction box, due to their weight it is important that the box be adequately secured to the ceiling structure.

The maximum amperage of the rail is 50 amps （each circuit is 25 amps）. You may run 600 watts on a 24 volt system (25 amps) or 300/600 watts on a 12 volt system (also 25 amps). Our 600 watt transformers are available in 12 or 24 volts. The 12 volt version has two outputs with 300 watts available at each.

WAC Magnetic Monorail Surface Mount Transformers for Duorail

Larger magnetic transformers have greater wattage capacities. There is a lesser degree of voltage drop in a magnetic transformer, making them a more practical choice for longer runs (see voltage drop guidelines).

Magnetic transformers generally contain less components making them among the most reliable power sources.

A magnetic transformer generally requires a low voltage dimmer specifically made for magnetic loads. However some of our remote magnetic transformers have the ability to be dimmed with standard incandescent dimmers.

Debuzzing coil

Inherent with all magnetic transformers is an audible buzz, mostly when dimmed. To lessen the noise, our surface mount transformers are supplied with a factory installed debuzzing coil (or choke).

Installing a Surface Mounted Transformer

  • The junction box will support the entire weight of the transformer, which may weigh up to 30 lbs.; make sure it is adequately braced and supported. It is recommended that two people install the transformer.
  • Extension wires are supplied to connect junction box wires to the transformer input wires. Connect white and grey neutral wire to white wire, and black and red hot wire to black wire with wire nuts. The ground wire may be green or bare copper, connect it to the green Extension wire.
  • Pass the open ends of the wires through the center hole of the cross bar/ threaded tube assembly, and mount to cross bar junction box as shown.
  • Open the transformer case by removing the four screws on the perimeter. The cover halves will separate but not detach, allow the lower half to hang temporarily.
  • Raise the transformer assembly on to the threaded tube and pass the ends of the wires through. Attach the heavy nut to the bottom of the tube and tighten so the transformer assembly is close to the ceilling.
  • Insert pin through hole on bottom of treaded tube to secure heavy nut to tube.
  • Connect the Extension wires to the transformer input wires, with wire nuts. Follow the previous color code.
  • Position the bottom cover so the power feed adapter is aligned to receive rail. Close the bottom cover and secure with the four secrews removed earlier.


WAC 300W 12V Magnetic LM2-EN12-300M Duorail Integrated Transformer

Surface mount magnetic low voltage transformer for the WAC Duorail system. The canopy style enclosure includes the transformer and the track power feed adaptor.
LM2 = Low voltage Duorail
EN12 = 12 volt, enclosed canopy transformer
300M = 300 watt magnetic

  • Use with standard standoff (LM2-X8)
  • Separate input leads fo separate switching
  • Voltage Drop Guidelines - Run Length 40'

The LM2-EN12-300M model has two 150w feeds.
Dims with magnetic low voltage dimmers.
Output circuit breaker located on the upper lip of the canopy enclosure is a magnetic push to reset type.
Contains integral de-buzzing coil.
The surface mount canopy transformer is an ideal choice when the installation is on an existing ceiling.

Input: 120V (50/60Hz)
Output: 12V
Min Load: 20W
Max Load: 300W
Max Input Amp: 2X2.5A (@ 120V)
Mounting: Installs to a standard junction box. Total weight = 11 lbs.
The standard LM2-EN12-300M configuration matches the height of the 8 1/16" standoffs (LM2-X8).

Finish: DB-Dark Bronze, BN - Brushed Nickel
Dimension: 9"

UL & CUL Listed.
5 year WAC Lighting product warranty.

LM2-EN12-300M-BN  Low Voltage Duorail 300W Magnetic Transformer
LM2-EN12-300M-DB  Low Voltage Duorail 300W Magnetic Transformer

WAC 500W 12V Magnetic LM2-EN12-500M Duorail Integrated Transformer

Surface mount magnetic low voltage transformer for the WAC Duorail system. The canopy style enclosure includes the transformer and the track power feed adaptors.
LM2 = Low voltage Duorail
EN12 = 12 volt, enclosed canopy transformer
500M = 500 watt magnetic

  • Use with standard standoff (LM2-X8)
  • Separate input leads fo separate switching
  • Voltage Drop Guidelines - Run Length 2 x 40'

The LM2-EN12-500M model has two 250w feeds.
Dims with magnetic low voltage dimmers.
The output circuit breakers located on the upper lip of the canopy enclosure are a magnetic push to reset type.
Contains integral de-buzzing coil.
The surface mount canopy transformer is an ideal choice when the installation is on an existing ceiling.

Input: 120V (60Hz)
Output: 12V
Max Load: 500W (2 x 250W circuits)
Max Input Amp: 2X2.5A (@ 120V)
Mounting: Installs to a standard junction box. Total weight = 25 lbs.
The standard LM2-EN12 configuration matches the height of the 8 1/16" standoffs (LM2-X8).

Finish: DB-Dark Bronze, BN - Brushed Nickel
Dimension: 10.25"

UL & CUL Listed.
5 year WAC Lighting product warranty.

LM2-EN12-500M-BN  Low Voltage Duorail 500W Magnetic Transformer
LM2-EN12-500M-DB  Low Voltage Duorail 500W Magnetic Transformer

Power Feed (if you choose a remote transformer)

Installing a Ceiling Power Feed

  • Position the transformer or power feed canopy, so the power feed adapters align with the rail.
  • Loosen the set screw in the adapter, so that there is sufficient clearence to slip the duo rail between the two halves.
  • Check the fit of the rail, to make sure it fits flat against the adapter channel. Complete contact is necessary for propper performance.
  • After the first 1/2 hour of operation, switch off and check connections for excessive heat or color distortion. Low voltage systems operate at higher amperage, which requires secure connections., A loose connection can lead to system damage and potential fire hazzard. Correct by tighteni ng, but do not over tighten. The recheck the hot spot to make certain it's corrected


Duorail Power Feeds (use with remote transformer)

WAC Lighting Duorail Cable Power Feed LM2-PCS

WAC Lighting Duorail 2 Circuit Cable Suspension Power Feed on Amazon

LM2-PCS48 2-Circuit Low Voltage Monorail Cable Power Feed
LM2-PCS96 2-Circuit Low Voltage Monorail Cable Power Feed

  • Use on sloped ceilings with remote transformers
  • Use with surface mounted transformer
  • Use at any angle, easily shortened

Finishes: BN-Brushed Nickel, DB-Dark Bronze



WAC Lighting Duorail Sloped Ceiling Feed LM2-SCP

WAC Lighting 48" Duorail Sloped Ceiling Power Feed on Amazon
WAC Lighting 96" Duorail Sloped Ceiling Power Feed on Amazon

LM2-SCP48 Low Voltage Duorail Sloped Ceiling Power Feed
LM2-SCP96 Low Voltage Duorail Sloped Ceiling Power Feed

  • Used with surface mounted transformer
  • Use at any angle, easily shortened
  • Includes two LM-RI couplers

Finishes: BN-Brushed Nickel, DB-Dark Bronze


WAC Lighting Dual Power Feed LM2-DCPC

WAC Lighting Dual Power Feed on Amazon

LM2-DCPC 2-Circuit Low Voltage Monorail Dual Power Feed

  • Feeds Four 25A max power feeds
  • Order with dead end "I" connector (LM2-IDEC)
  • Use with 3" standoff (LM2-X3)

Dimension: 5.125"

Finishes: BN-Brushed Nickel, DB-Dark Bronze



WAC Lighting Single Power Feed LM2-CPC

WAC Lighting Single Power Feed on Amazon

LM2-CPC 2-Circuit Low Voltage Monorail Single Power Feed

  • Feeds two 25A max circuits
  • Use with 3" standoff (LM2-X3)

Dimension: 4.5"

Finishes: BN-Brushed Nickel, DB-Dark Bronze

Magnetic Duorail Remote Transformers

WAC Magnetic Monorail Remote Transformers for Duorail

The larger magnetic transformers have greater wattage capacities. There is a lesser degree of voltage drop in a magnetic transformer, making them a more practical choice for longer runs (see voltage drop guidelines). Magnetic transformers generally contain less components making them among the most reliable power sources.

A magnetic transformer generally requires a low voltage dimmer specifically made for magnetic loads. However some of our remote magnetic transformers have the ability to be dimmed with standard incandescent dimmers.

DuoRail system works with 12 or 24 volts, so transformers are available for either voltage. The maximum amperage of the rail is 50 amps （one circuit is 25 amps ）. You may run 600 watts on a 24 volt system (25 amps) or 300/600 watts on a 12 volt system (also 25 amps). Our 600 watt transformers are offered in 12 or 24 volts. The 12 volt version has two outputs with 300 watts available at each.

Debuzzing coil

Inherent with all magnetic transformers is an audible buzz, mostly when dimmed. A debuzzing coil is an option on remote magnetic transformers. Debuzzing coils are installed between the switch and transformer on the black (hot) primary wire.

Installing a Remote Transformer

  • Locate the transformer as close as possible to the power feed point to minimize voltage drop.
  • Connect line voltage wires to their respective transformer input wires, (white to white & black to black).
  • Make ground wire connection.
    Note: Some remote transformers have integral enclosures with a green wire, if not, an enclosure is required. Establish a ground connection to the enclosure.
  • To wire secondary wires, first determine the appropriate THHN wire gauge size for the distance between the transformer and the junction box (see voltage drop guidelines). Run secondary wires from transformer to power in walls and ceilings should be enclosed type ie: BX, Romex, MC.
  • Select a knock out hole in the power fe ed canopy back plate.
  • Support the power feed canopy, and route wires from the canopy through the the knock out hole into the junction box.
  • Attach canopy wires to the transformer wires with wire nuts (supplied). Tuck wires back into the junction box.
  • Secure the base plate to the junction box, through the slotted holes.
  • Loosen the three screws on the canopy. Raise the power feed canopy to the base plate and partially tighten screws so that they support the weight of the canopy.
  • Rotate the canopy so the power feed adapter aligns with the rail, then fully tighten screws.
  • For locations where no junction box is present secure the back plate to the surface, and make wire connections in the canopy.
  • Note: Low voltage systems require firm connections at all points, to avoid abnormal heat conditions. A loose connection can lead to system damage and potential fire hazzard. Correct by tightening, but do not over tighten. Recheck the hot spot to make certain it's corrected.
SRT-1000M-12V

12V 1000W Magnetic SRT-1000M-12V

Remote Magnetic Transformer 12V
SRT-300M-12V

12V 300W Magnetic SRT-300M-12V

Remote Magnetic Transformer 12V
SRT-600M2-12V

12V 600W Independent Circuit SRT-600M2-12V

Remote Magnetic Transformer 2X300W 12V
SRT-600M-12V

12V 600W Magnetic SRT-600M-12V

Remote Magnetic Transformer12V
SRT-1000M-24V

24V 1000W Magnetic SRT-1000M-24V

Remote Magnetic Transformer 24V
SRT-300M-24V

24V 300W Magnetic SRT-300M-24V

Remote Magnetic Transformer 12V
SRT-600M-24V

24V 600W Magnetic SRT-600M-24V

Remote Magnetic Transformer24V

WAC Transformers & Accessories >

Quick Connect Pendants for Solorail

WAC Lighting DuoRail 2-Circuit Monorail with LEDme Forza LED QF-LED173 Quick Connect Fixtures and Uber G315 LED Pendants from the Industrial Collection all in Satin Nickel Finish

WAC Lighting Duorail Pendants and Fixtures

Choose from WAC Lightings vast selection of Pendants in so many colors and styles.

Duorail uses low voltage track heads and pendants. The Duorail system uses LM2 style track heads as well as quick connect track heads and pendants in conjunction with the LM2-QADP quick connect adaptor.

WAC Transformers & Accessories >

WAC Lighting Quick Connect Fixtures for Monorail

Modern styles, decorative yet functional. The Quick Connect Series of low voltage track heads includes a selection of 12 styles and a wide variety glass and metal shielding options.

All Quick Connect track head stems are available with standard stem lengths from 3" to 12" so they can be low profile or closer to the action.

Quick Connect fixtures all have a male adapter. With the appropriate adapter, they can be mounted on a variety of track, rail and surface mount systems.

WAC Lighting Quick Connect Fixtures & LED Fixtures >



WAC Quick Connect Pendants for Monorail

Wac Lighting Quick Connect Pendants can be used suspended from Solorail Monorail or 2-Circuit Duorail Monorail using the correct adapter. Because the monorail is 12 volt, no transformer is required.

WAC Lighting Artisan Pendants

This unique collection includes iridescent pendants with hand painted backgrounds in blue, green, rose and gold. The Brittany and Mini Brittany have layers of classic Italian opaline glass crafted into dramatic opalescent flowers in gorgeous hues of amber, gold and milky blue come. The Rococo pendant has beautiful mouth blown art glass hand crafted by fine Italian artisans with amber and opal frit, richly layered in speckles of gold.

Artisan Pendants >



WAC Lighting Contemporary Pendants

These sophisticated mouth blown, cased glass pendants create a soft glow. Choose from a variety of shapes and colors. The unique Micha pendant is hand crafted from pieces of crushed glass. No two pendants are identical with unique patterns and textures.

Contemporary Pendants >



WAC Lighting European Pendants

Crafted by some of the world's most highly skilled artisans, these pendants feature dichroic art glass, colored glass, unique iridescent glass, murrine glass and other glass in a variety of shapes, colors and patterns.

European Pendants >



WAC Lighting Early Electric Collection
Nostalgic design transformed beautifully into energy efficient LED pendants

Pendants Light your entire kitchen with less than 100 watts of energy. The industrial look of yesteryear with well-proportioned design. These vintage stylee incorporates exposed hardware in a glare-free miniaturized LED versions in beautiful finishes. Using just 5 watts of energy, these nostalgic pendants provide warm illumination but are cool to the touch.

Early Electric Pendants >



WAC Lighting Eternity Jewelry Collection
A modern twist on crystal

Breathtaking clusters of sparkle and brilliance. A myriad of glistening crystals add an exquisite touch to the most sophisticated decor. Modern lights developed with proprietary LED technology and old world artisanship. These elegant pendants add more than just ambiance providing generous light sufficient for tasks.

Eternity Jewelry Collection >



Duorail Quick Connect Adapter LM2-QADP

Duorail system quick connect adaptor allows all quick connect elements (QF track heads or QP pendants) to be used with the LM2 system rail. The adaptor contains a threaded nipple for quick connect socket sets and attaches anywhere along the LM2 track. One adaptor must be ordered for each quick connect element used on a system.

  • Quick connect adaptor allows all quick connect elements to be used with the LM system rail
  • The adaptor contains a threaded nipple for quick connect socket sets and attaches anywhere along the LM track

    Available in Brushed Nickel (BN) or Dark Bronze (DB).

*Order one per Quick Connect fixture or pendant used

LM2-QADP-BN 2-Circuit Low Voltage Monorail QC Female Adapter  
LM2-QADP-DB 2-Circuit Low Voltage Monorail QC Female Adapter  

The threaded male adapter makes compatibility a snap.
Simply insert the metal fitting into the system adapter, hand tighten the collar and you're done!



Quick Connect Q-X Fixture Extension

Designed for use with Quick Connect track fixtures to extend the stem

Cannot be shortened in the field

Q-X18-BN 18" Brushed Nickel
Q-X18-DB 18" Dark Bronze
Q-X24-BN 24" Brushed Nickel
Q-X24-DB 24" Dark Bronze
Q-X36-BN 36" Brushed Nickel
Q-X36-DB 36" Dark Bronze
Q-X48-BN 48" Brushed Nickel
Q-X48-DB 48" Dark Bronze

WAC Lighting Low Voltage 2-Circuit Duorail Monorail Installation Instructions & Frequently Asked Questions >


Related Pages

Wall or Ceiling Spotlights and Fixed Monorails
Wall or Ceiling Spotlights and Fixed Monorails

WAC Quick Connect Early Electric Pendants

WAC Quick Connect Fixtures

As an eBay Partner and Amazon Associate I earn from qualifying purchases. Find out more >

Return to top of page

Indoor Lighting l Outdoor Lighting l Table, Floor & Desk Lamps l Kitchen, Recessed & Track Lighting l Fans
Site Map

Copyright © 2018 - 2024 design42 New Media Web Design. All rights reserved.


design42 New Media Web Design
2192 Dartmouth Rd
Hendersonville NC 28791