Line Voltage Monorail

WAC Low Voltage or Line Voltage Monorail Quick Connect Fixtures & Pendants

Accessories

WAC Shades, Shields, Lenses & Accessories

This site contains affiliate links for which I may be compensated.

WAC Lighting SoloRail Monorail System (Retired)

WAC Lighting Solorail with QF-190 Rolls Quick Connect Fixtures on 3" stems with G-119 Amber shades
Rail is curved both vertically and horizontally.

Customize Your WAC Lighting SoloRail Monorail System

WAC Solorail
Single Circuit Monorail System

WAC Lighting low voltage monorail system can be shaped in the field and designed and cut to navigate curves for custom designs. WAC Solorail has a maximum capacity of 300 watts at 12 volts and 600 watts at 24 volts.

Design your rail.

Determine what you want to light.
Decide where track heads, pendants or both will be placed to direct light where you want it.
Design the Monorail run, connecting the lights.
Monorail can be shaped to follow room architecture or create an organic shape.
You can sketch out your room on paper. Draw in your lights, then decide how you want to design the track to suspend them.
You could use string to lay out your design on the floor to determine your length, especially if you have an especially curvy run.
Rail is available in connectable four or eight foot sections to be bent in the field as needed or used as a straight section. A bending machine is available to make smooth and consistent bends.
All rail pieces are field-cuttable and bendable.
Connectors allow monorail to make sharp angles or join in a "T" or " x ."
Dead-End connectors allow you to switch and dim sections of rail separately.
Choose a finish; Brushed Nickel or Dark Bronze.
Or choose a kit for a lower cost simple setup.

Determine your mounting.

Determine how far from the ceiling you would you like your rail to run.
WAC Solorail Monorail can be installed cantilevered from the wall, nearly flush to the ceiling or hang up to 96".
Rail can be curved horizontally or vertically, to run up and down.
Rigid or cable suspensions mount to flat, suspended or sloped ceilings using standard, T-Bar or sloped ceilings standoffs.
Use 2 supports per 4 foot section and at least 3 per 8 foot section.
Two wall support choices are available.
The total number of supports depends on the shape of the track layout.
The power feed counts as a support.
Systems with very unique shapes or many pendants may require additional supports.

Choose your lights.

Decide where the fixtures should be installed to put light where you want it.
Select from an array of low voltage track heads and pendants.
Extension stems can extend fixtures up to 48" from the track.
Pendants ship with 6' field cuttable cable.
Add optional colorful and decorative accessories and functional optical controls.

Select your transformer.

Add up the wattage from the lights you have chosen.
Choose 12 or 24 volt. 300 watts is the maximum load for 12 volt systems. 600 watts is the maximum load for 24 volt systems.
Select a visible surface mount transformer or a hidden remote transformer with power feed canopy.
Surface mount transformers install directly to a standard junction box.
Smaller electronic surface mount transformers are well suited for small runs.
Magnetic surface mount tranformers have a higher wattage capacity.
Remote mount magnetic transformers have even larger capacity. They can be installed further away, in an attic or closet.
Magnetic transformers minimize any voltage drop potential.
Select your power feed if you are going to use a remote transformer.

(Or start with fixtures and accessories, then decide which layout will best support them.)

WAC Lighting Low Voltage Solorail Monorail Installation Instructions & Frequently Asked Questions >

Rail

WAC Lighting LM-T Solorail Monorail Systems

WAC Solorail is a low voltage bendable single circuit track system. Straight rail is ordered as a four or eight foot sections to be bent in the field as needed or used as a straight section. The rail is field cuttable and bendable by hand or with a bending tool.

Solorail is composed of two 1.9mm thick copper bus wires with 1.5mm thick polycarbonate core. Each rail also includes two matching polycarbonate end caps.

1 circuit, 12 volt or 24 volt.
300W maximum capacity at 12V.
600W maximum capacity at 24V.
Can use electronic surface mount, electronic remote, magnetic surface mount, or magnetic remote transformers.
Mounts to flat, suspended, or sloped ceilings. Use 2 supports per 4 foot section and at least 3 per 8 foot section. Total number of supports used in an application depends on the shape of the track layout. Systems with very unique shapes may require the use of additional supports.
The LM-QADP is compatible with all QF and QP socket sets.
Can be suspended from ceiling with cable or rigid standoffs. Suspension support information can be found on the Solorail Suspension spec sheet.
An optional rail bending tool (LM-BM) is available for field bending when precise control and very smooth curves are desired.
Abrasion resistant Bronze or Brushed Nickel finish.

BN = Brushed Nickel metal finish
DB = Dark Bronze metal finish

5 year WAC Lighting product warranty.
UL & CUL Listed.

LM-T4-BN	Low Voltage Monorail 4 Ft Rail
LM-T4-DB	Low Voltage Monorail 4 Ft Rail
LM-T8-BN	Low Voltage Monorail 8 Ft Rail
LM-T8-DB	Low Voltage Monorail 8 Ft Rail

Bending Machine HM1-BM

Monorail Bending Machines on Amazon

Used to make smooth and consistent bends of rail. Two Compact and Mini Picture Lights brackets mount bending machine to table or similar flat surface. Angle indicators on bending machine help the user determine the proper amount of tension.

This same bending machine will bend a variety of monorail.

HM1-BM

Bending Machine

Connectors

T Connector LM-T-color Solorail System

Connects two sections of rail in a "T" with electrical continuity.
Allows seamless connection of rail sections.

LM-T-BN	Low Voltage Monorail T Connector
LM-T-DB	Low Voltage Monorail T Connector

"L" Connector LM-L Solorail System

90° monorail connection with electrical continuity. Allows seamless connection of rail sections.

Dimension: 5/8" x 1.5" x 1.5"

LM-L-BN	Low Voltage Monorail L Connector
LM-L-DB	Low Voltage Monorail L Connector

Variable Angle Connector LM-VA Solorail System

Allows an angle adjustment up to 110° with electrical continuity at the connection

Dimension: 1" x 1.25" x 3.5"

LM-VA-BN	Variable Angle Connector
LM-VA-DB	Variable Angle Connector

" x " Dead-End Connector LM-XDEC Solorail System

Joins four monorails in an " x " without electrical continuity

Dimension: 5/8" x 2" x 2"

LM-XDEC-BN	Low Voltage Monorail X Connector
LM-XDEC-DB	Low Voltage Monorail X Connector

"I" Connector LM-I Solorail System

Connects two sections of rail with electrical continuity

Dimension: 5/8" x 2"

LM-I-BN	Low Voltage Monorail I Connector
LM-I-DB	Low Voltage Monorail I Connector

"I" Dead-End Connector LM-IDEC Solorail System

Connects two sections of rail with no electrical continuity

Dimension: 5/8" x 2"

LM-IDEC-BN	Low Voltage Monorail Dead End Straight Connector
LM-IDEC-DB	Low Voltage Monorail Dead End Straight Connector

Solorail End Cap LM-EC

Extra end cap for Solorail.
Each rail also includes two matching polycarbonate end caps.
Order additional endcaps if you are doing multiple cuts of a long piece of rail.

LM-EC-BN	Low Voltage Monorail -End Cap
LM-EC-DB	Low Voltage Monorail -End Cap

Mounting

Standard Ceiling Standoff LM-X Solorail System

Supports rail for flat ceilings and surfaces

LM-X3 3"
LM-X4 4.5"
LM-X5 5.75"

LM-X3-BN	Low Voltage Monorail 3" Suspension
LM-X3-DB	Low Voltage Monorail 3" Suspension
LM-X4-BN	Low Voltage Monorail 4.5" Suspension
LM-X4-DB	Low Voltage Monorail 4.5" Suspension
LM-X5-BN	Low Voltage Monorail 5.75" Suspension
LM-X5-DB	Low Voltage Monorail 5.75" Suspension

T-Bar Drop Ceiling Suspension LM-TB3 Solorail System

Conceals a T-Bar clip under the canopy for standard 1" T-Bar ceilings

TB3 - 3"
TB4 - 4.5"
TB5- 6"

LM-TB3-BN	Low Voltage Monorail Drop Ceiling Suspension 3"
LM-TB3-DB	Low Voltage Monorail Drop Ceiling Suspension 3"
LM-TB4-BN	Low Voltage Monorail drop Ceiling Suspension 4.5"
LM-TB4-DB	Low Voltage Monorail drop Ceiling Suspension 4.5"
LM-TB5-BN	Low Voltage Monorail Drop Ceiling Suspension 6"
LM-TB5-DB	Low Voltage Monorail Drop Ceiling Suspension 6"

WAC Lighting Sloped Ceiling Standoff LM-XS Solorail System

Support rail for slope ceiling

Accommodates angles up to 45"

Dimension 5.75"

LM-XS5-BN	Low Voltage Monorail 5" Sloped Ceiling Standoff
LM-XS5-DB	Low Voltage Monorail 5" Sloped Ceiling Standoff

WAC Lighting Extension Rods LM-R for Solorail Monorail Support

Use with standoffs and power feed
Use two per circuit with rod couplers to extend power feeds
Field cut to size and join with rod couplers

Finishes: BN-Brushed Nickel, DB-Dark Bronze

LM-R12-BN	Low Voltage Monorail 12" Extension Rod
LM-R12-DB	Low Voltage Monorail 12" Extension Rod
LM-R24-BN	Low Voltage Monorail 2Extension 4" Rod
LM-R24-DB	Low Voltage Monorail 2Extension 4" Rod
LM-R36-BN	Low Voltage Monorail 36" Extension Rod
LM-R36-DB	Low Voltage Monorail 36" Extension Rod
LM-R48-BN	Low Voltage Monorail 48" Extension Rod
LM-R48-DB	Low Voltage Monorail 48" Extension Rod

Rod Coupler LM-RI Low Voltage Monorail Rod Coupler

LM-RI-BN Brushed Nickel
LM-RI-DB Dark Bronze

Use two per power feed, four per dual power feed, one additional coupler per rod needed when joining two rods in excess of 48".

Aircraft Suspension Cable LM-CS Solorail System

Supports monorail for flat or slope ceilings

LM-CS48 - 48"
LM-CS96 - 96"

LM-CS48-BN	Low Voltage Monorail Cable Ceiling Suspension 48"
LM-CS48-DB	Low Voltage Monorail Cable Ceiling Suspension 48"
LM-CS96-BN	Low Voltage Monorail Cable Ceiling Suspension 96"
LM-CS96-DB	Low Voltage Monorail Cable Ceiling Suspension 96"

WAC Lighting Wall Mount Support Bracket LM-OW

LM-OW Low Voltage Monorail Wall Extension Bracket Support
Use with LM-OWP-BN Low Voltage Monorail Wall Extension Bracket Power Feed

Wall extenders allow rail to be mounted up to 24" from wall

Can be mounted up to 24" from wall
Supported by aircraft cables
Use with remote transformers
Use with two Wall Mount Support Brackets (LM-OW) per 4ft, and three per 8ft

Finishes: BN-Brushed Nickel, DB-Dark Bronze

Solorail Surface Mounted Transformers

Surface mount transformers mount to a junction box, due to their weight it is important that the box be adequately secured to the ceiling structure.

Because the monorail system works with 12 or 24 volts we offer transformers for either voltage. The maximum amperage of the rail is 25 amps. You may run 600 watts on a 24 volt system (25 amps) or 300 watts on a 12 volt system (also 25 amps). Our 600 watt transformers are offered in 12 or 24 volts, however the 12 volt version has two outputs with 300 watts available at each.

WAC Electronic Monorail Surface Mount Transformers for Solorail

Either electronic or magnetic transformers can power mono rail. Electronics are smaller than magnetic. Electronic transformers offer quieter operation than magnetics, making them a more practical choice for quiet settings. (see voltage drop guidelines).

An electronic transformer will work with most standard incandescent dimmers.

WAC Magnetic Monorail Surface Mount Transformers for Solorail

Larger magnetic transformers have greater wattage capacities. There is a lesser degree of voltage drop in a magnetic transformer, making them a more practical choice for longer runs (see voltage drop guidelines).

Magnetic transformers generally contain less components making them among the most reliable power sources.

A magnetic transformer generally requires a low voltage dimmer specifically made for magnetic loads. However some of our remote magnetic transformers have the ability to be dimmed with standard incandescent dimmers.

Debuzzing coil

Inherent with all magnetic transformers is an audible buzz, mostly when dimmed. To lessen the noise, our surface mount transformers are supplied with a factory installed debuzzing coil (or choke).

Installing a Surface Mounted Transformer

The junction box will support the entire weight of the transformer, which may weigh up to 30 lbs.; make sure it is adequately braced and supported. It is recommended that two people install the transformer.
Extension wires are supplied to connect junction box wires to the transformer input wires. Connect white and grey neutral wire to white wire, and black and red hot wire to black wire with wire nuts. The ground wire may be green or bare copper, connect it to the green Extension wire.
Pass the open ends of the wires through the center hole of the cross bar/ threaded tube assembly, and mount to cross bar junction box as shown.
Open the transformer case by removing the four screws on the perimeter. The cover halves will separate but not detach, allow the lower half to hang temporarily.
Raise the transformer assembly on to the threaded tube and pass the ends of the wires through. Attach the heavy nut to the bottom of the tube and tighten so the transformer assembly is close to the ceilling.
Insert pin through hole on bottom of treaded tube to secure heavy nut to tube.
Connect the Extension wires to the transformer input wires, with wire nuts. Follow the previous color code.
Position the bottom cover so the power feed adapter is aligned to receive rail. Close the bottom cover and secure with the four secrews removed earlier.

WAC LM-EN12-150E/250E Electronic Solorail Monorail Transformer

LV Monorail-Surface Mount Electronic 12V 150W
LV Monorail-Surface Mount Electronic 12V 250W

Use with standard standoff: 4.5" (LM-X4).

Model No.	wide	Voltage	Wattage
LM-EN12-150E	5"	12v	150w
LM-EN12-250E	6"	12v	250w

Finish: DB-Dark Bronze, BN - Brushed Nickel

WAC LM-EN12-150M Magnetic Monorail Transformers

LV Monorail-Surface Mount Transformer 12V

Use with standard standoff: 5.75" (LM-X5)

Model No.	Voltage	Wattage
LM-EN12-150M	12v	150w

Finish: DB-Dark Bronze, BN - Brushed Nickel
wide 7 5/8"

WAC 300W 12V Magnetic LM-EN12-300M Solorail Integrated Transformer

Surface mount magnetic low voltage transformer for the WAC Solorail system. The canopy style enclosure includes the transformer and the track power feed adaptor.
LM = Low voltage Solorail
EN12 = 12 volt, enclosed canopy transformer
300M = 300 watt magnetic

Use with standard standoff (LM2-X8)
Separate input leads fo separate switching
Voltage Drop Guidelines - Run Length 40'

Dims with magnetic low voltage dimmers.
Output circuit breaker located on the upper lip of the canopy enclosure is a magnetic push to reset type.
Contains integral de-buzzing coil.
The surface mount canopy transformer is an ideal choice when the installation is on an existing ceiling.

Input: 120V (50/60Hz)
Output: 12V
Max Load: 300W
Max Input Amp: 2.5A (@ 120V)
Mounting: Installs to a standard junction box. Total weight = 11 lbs.
The standard LM-EN12-300M configuration matches the height
of the 5 ¾" standoffs (LM-X5).

LV Monorail-Surface Mount Transformer 12V 300W

Use with standard standoff: 5.75" (LM-X5).

Model No.	Voltage	Wattage
LM-EN12-300M	12v	300w

Finish: DB-Dark Bronze, BN - Brushed Nickel
9" wide

UL & CUL Listed.
5 year WAC Lighting product warranty.

WAC LM-EN12-600M Magnetic Monorail Transformers

LV Monorail-Surface Mount Transformer 12V 600W

Use with standard standoff: 5.75" (LM-X5)

Model No.	Voltage	Wattage
LM-EN12-600M	12v(2x300w)	300w

Finish: DB-Dark Bronze, BN - Brushed Nickel
wide 10.5"

WAC LM-EN24-600M Magnetic Monorail Transformers

LV Monorail-Surface Mount Transformer 24V 600W

Use with standard standoff: 5.75" (LM-X5)

Model No.	Voltage	Wattage
LM-EN24-600M	24v	600w

Finish: DB-Dark Bronze, BN - Brushed Nickel
wide 10.5"

Power Feed (if you choose a remote transformer)

WAC Lighting Cable Power Feed LM-PCS

LM-PCS48 Low Voltage Monorail Cable Susp Power Feed 48"
LM-PCS96 Low Voltage Monorail Cable Susp Pwr Feed 96"

25A max
Use on sloped ceilings with surface mounted OR remote transformers
Use at any angle, can be easily shortened

Length 4 1/2 x 48"

Finishes: BN-Brushed Nickel, DB-Dark Bronze

WAC Lighting Dual Power Feed LM-DCPC

LM-DCPC Low Voltage Monorail Close To Ceiling Pwr FeedDual

Two 25A max power feeds
Order with dead end "I" connector (LM-IDEC) and use with 3" standoffs (LM-X3)

Dimension: 5 1/8"

Finishes: BN-Brushed Nickel, DB-Dark Bronze

WAC Lighting Single Power Feed LM-CPC

LM-CPC Low Voltage Monorail Close To Ceiling Power Feed

25A max
Use with 3" standoff (LM-X3)

Dimension: 4.5"

Finishes: BN-Brushed Nickel, DB-Dark Bronze

WAC Lighting Sloped Ceiling Feed LM-SCP

LM-SCP48 Low Voltage Monorail Slope Ceiling Pwr ADAp 48"
LM-SCP96 Low Voltage Monorail Slope Ceiling Pwr ADAp 96"

25A max
Use with surface mounted transformer
Use at any angle, can be easily shortened
Includes two LM-RI couplers

Finishes: BN-Brushed Nickel, DB-Dark Bronze

WAC Lighting Wall Mount Power Feed Bracket LM-OWP

LM-OWP Low Voltage Monorail Wall Extension Bracket Pwr Feed
Use with Wall Mount Support Bracket LM-OW

Wall extenders allow rail to be mounted up to 24" from wall

Can be mounted up to 24" from wall
Supported by aircraft cables
Use with remote transformers
Use with two Wall Mount Support Brackets (LM-OW) per 4ft, and three per 8ft

Finishes: BN-Brushed Nickel, DB-Dark Bronze

WAC Lighting Wall Power Feed LM-WPC

LM-WPC Low Voltage Monorail Wall Power Feed
The wall mount power feed installation is the same as ceilling mount.
It differs from the ceiling mount in that the power feed adapter is shaped to accept rail from it's end.

25A max
Feeds power to end of the rail

Dimension: 4.5"

Finishes: BN-Brushed Nickel, DB-Dark Bronze

Rod Coupler LM-RI Low Voltage Monorail Rod Coupler

LM-RI-BN Brushed Nickel
LM-RI-DB Dark Bronze

Use two per power feed, four per dual power feed, one additional coupler per rod needed when joining two rods in excess of 48".

Magnetic Monorail Remote Transformers

WAC Magnetic Monorail Remote Transformers for Solorail

The larger magnetic transformers have greater wattage capacities. There is a lesser degree of voltage drop in a magnetic transformer, making them a more practical choice for longer runs (see voltage drop guidelines).

Most of our remote magnetic transformers have a boost tap option, which allows the transformer to be wired for a slightly higher (approximately 10%)voltage output to compensate for voltage drop. To use see instructions furnished with the transformer.

Debuzzing coil

Inherent with all magnetic transformers is an audible buzz, mostly when dimmed. A debuzzing coil is an option on remote magnetic transformers. Debuzzing coils are installed between the switch and transformer on the black (hot) primary wire.

Installing a Remote Transformer

Locate the transformer as close as possible to the power feed point to minimize voltage drop.
Connect line voltage wires to their respective transformer input wires, (white to white & black to black).
Make ground wire connection.
Note: Some remote transformers have integral enclosures with a green wire, if not, an enclosure is required. Establish a ground connection to the enclosure.
To wire secondary wires, first determine the appropriate THHN wire gauge size for the distance between the transformer and the junction box (see voltage drop guidelines). Run secondary wires from transformer to power in walls and ceilings should be enclosed type ie: BX, Romex, MC.
Select a knock out hole in the power fe ed canopy back plate.
Support the power feed canopy, and route wires from the canopy through the the knock out hole into the junction box.
Attach canopy wires to the transformer wires with wire nuts (supplied). Tuck wires back into the junction box.
Secure the base plate to the junction box, through the slotted holes.
Loosen the three screws on the canopy. Raise the power feed canopy to the base plate and partially tighten screws so that they support the weight of the canopy.
Rotate the canopy so the power feed adapter aligns with the rail, then fully tighten screws.
For locations where no junction box is present secure the back plate to the surface, and make wire connections in the canopy.
Note: Low voltage systems require firm connections at all points, to avoid abnormal heat conditions. A loose connection can lead to system damage and potential fire hazzard. Correct by tightening, but do not over tighten. Recheck the hot spot to make certain it's corrected.

	SRT-300M-12V	Remote Magnetic Transformer 12V 300W
	SRT-600M-12V	Remote Magnetic Transformer12V 600W
	SRT-300M-24V	Remote Magnetic Transformer 24V 300W
	SRT-600M-24V	Remote Magnetic Transformer24V 600W
More WAC Transformers & Accessories >

Quick Connect Pendants & Fixtures for Solorail

WAC Lighting SoloRail Monorail with QF-186 Americana Quick Connect Fixtures with 3" & 6" stems and G111 White Glass Shades and Brittany MP-LED333 LED Pendants from the European Collection all in Dark Bronze Finish

WAC Lighting SoloRail Pendants and Fixtures

Choose from WAC Lightings vast selection of Pendants in so many colors and styles.

Solorail uses low voltage track heads and pendants. The Solorail system uses LM style track heads as well as quick connect track heads and pendants in conjunction with the LM-QADP Quick Connect adaptor.

The Q-X Quick Connect Fixture Extension can be used to extend the stem of any Solorail Track Light. The WAC Lighting Pendants ship with 6' of field adjustable cable.

WAC Lighting Quick Connect Fixtures for Monorail

Modern styles, decorative yet functional. The Quick Connect Series of low voltage track heads includes a selection of 12 styles and a wide variety glass and metal shielding options.

All Quick Connect track head stems are available with standard stem lengths from 3" to 12" so they can be low profile or closer to the action.

Quick Connect fixtures all have a male adapter. With the appropriate adapter, they can be mounted on a variety of track, rail and surface mount systems.

WAC Lighting Quick Connect Fixtures & LED Fixtures >

WAC Quick Connect Pendants for Monorail

Wac Lighting Quick Connect Pendants can be used suspended from Solorail Monorail using the correct adapter. Because the monorail is 12 volt, no transformer is required.

WAC Lighting Artisan Pendants

This unique collection includes iridescent pendants with hand painted backgrounds in blue, green, rose and gold. The Brittany and Mini Brittany have layers of classic Italian opaline glass crafted into dramatic opalescent flowers in gorgeous hues of amber, gold and milky blue come. The Rococo pendant has beautiful mouth blown art glass hand crafted by fine Italian artisans with amber and opal frit, richly layered in speckles of gold.

Artisan Pendants >

WAC Lighting Contemporary Pendants

These sophisticated mouth blown, cased glass pendants create a soft glow. Choose from a variety of shapes and colors. The unique Micha pendant is hand crafted from pieces of crushed glass. No two pendants are identical with unique patterns and textures.

Contemporary Pendants >

WAC Lighting European Pendants

Crafted by some of the world's most highly skilled artisans, these pendants feature dichroic art glass, colored glass, unique iridescent glass, murrine glass and other glass in a variety of shapes, colors and patterns.

European Pendants >

WAC Lighting Early Electric Collection
Nostalgic design transformed beautifully into energy efficient LED pendants

Pendants Light your entire kitchen with less than 100 watts of energy. The industrial look of yesteryear with well-proportioned design. These vintage stylee incorporates exposed hardware in a glare-free miniaturized LED versions in beautiful finishes. Using just 5 watts of energy, these nostalgic pendants provide warm illumination but are cool to the touch.

Early Electric Pendants >

WAC Lighting Eternity Jewelry Collection
A modern twist on crystal

Breathtaking clusters of sparkle and brilliance. A myriad of glistening crystals add an exquisite touch to the most sophisticated decor. Modern lights developed with proprietary LED technology and old world artisanship. These elegant pendants add more than just ambiance providing generous light sufficient for tasks.

Eternity Jewelry Collection >

Solorail Quick Connect Adapter LM-QADP

Solorail system quick connect adaptor allows all quick connect elements (QF track heads or QP pendants) to be used with the LM system rail. The adaptor contains a threaded nipple for quick connect socket sets and attaches anywhere along the LM track. One adaptor must be ordered for each quick connect element used on a system.

Order one per Quick Connect fixture or pendant used. The threaded male adapter makes compatibility a snap. Simply insert the metal fitting into the system adapter, hand tighten the collar and you're done!

Quick Connect adaptor allows all Quick Connect elements to be used with the Solorail system
The threaded male adapter makes compatibility a snap.
Simply insert the metal fitting into the system adapter, hand tighten the collar and you're done!

Available in Dark Bronze (DB) or Brushed Nickel (BN).

LM-QADP

BN-Brushed Nickel
DB-Dark Bronze

The threaded male adapter makes compatibility a snap.
Simply insert the metal fitting into the system adapter, hand tighten the collar and you're done!

Quick Connect Q-X Fixture Extension

Designed for use with Quick Connect track fixtures to extend the stem

Cannot be shortened in the field

Q-X18-BN	18"	Brushed Nickel
Q-X18-DB	18"	Dark Bronze
Q-X24-BN	24"	Brushed Nickel
Q-X24-DB	24"	Dark Bronze
Q-X36-BN	36"	Brushed Nickel
Q-X36-DB	36"	Dark Bronze
Q-X48-BN	48"	Brushed Nickel
Q-X48-DB	48"	Dark Bronze

WAC Lighting Low Voltage Solorail Monorail Installation Instructions & Frequently Asked Questions >

Track Lighting Pendants

WAC Quick Connect Early Electric Pendants

WAC Quick Connect Fixtures

Complete Monorail Kits l Monorail Idea Photos l Site Map

WAC Lighting SoloRail Monorail System (Retired)

Rail

Connectors

Mounting

Solorail Surface Mounted Transformers

Power Feed (if you choose a remote transformer)

Magnetic Monorail Remote Transformers

Quick Connect Pendants & Fixtures for Solorail

Related Pages